INAP395R

APIX2 Multichannel SerDes with 3 Gbps and HDCP support

The INAP395R is an APIX2 receiver device supporting the reception of copyright protected digital entertainment content. The device incorporates the decryption mechanisms as well as the required keys to receive HDCP 1.4 encoded video and audio content over the APIX2 link. APIX2 is a DC-balanced, AC coupled low latency, point-to-point link over shielded twisted pair (STP) copper cables. Its scalable physical layer provides bandwidth from 500 Mbps of up to 3 Gbps at lowest EMI. The INAP395R offers a flexible video interface, optimized for TFT panels or graphic processing SoCs, with input interfaces such as parallel RGB or OpenLDI LVDS. Software adjustable driver characteristics, selectable interfaces and configurable operating modes allow maximum transmission distances of up to 12m @ 3Gbps. In addition to the video transmission, the INAP395R allows completely independent full duplex communication channels. Using the internal AShell protocol, data transfers such as panel control or touch control information are protected by error detection and retransmission mechanisms.

The INAP395R offers various interfaces to directly drive and connect to graphic display- or touch controllers. Besides an I²C compliant interface, the link is optimized to carry low latency GPIO signals for reset or hardware signal switching. Various data integrity features like CRC on video data, monitoring of control signals support secure data transfer over the APIX2 link. The device is offered in a 100 pin LQFP package, and qualified according to the
AEC-Q100 automotive standards.

Features
  • Supports High-bandwidth Digital Content
  • Protection according to HDCP 1.4
  • Pin compatible to INAP375R
  • video data rates up to 2591 Mbps
  • up to 187.5 Mbps upstream link bandwidth
  • Supports 2 independent HDCP encrypted video streams
  • Configurable video interface
    – Parallel RGB (10,12,18 or 24 Bit)
    – openLDI compliant LVDS interface
    – Single Channel (18 or 24 Bit)
    – Dual Channel (18 or 24 Bit)
    – Parallel Bulk Data Mode (10,12,18,24 Bit)
  • Video resolutions up to HD resolutions
  • AShell protected full duplex communication channel
  • Daisy chain output to a 2nd receiver
  • Media Independent Interface
  • Media Independent Interface
  • Flexible data interface
    – SPI Master/slave
    – I²C Master
  • Optimized I²C Touchscreen controller support
  • Low latency GPIOs
  • I²S Audio interface
    – supports 16/24/32 Bit word length
    – supports up to 192kHz sampling
    – TDM support for up to 8 channels
  • Diagnostic Features:
    – Built-In PRBS Checker
    – Embedded diagnostics
  • Up to 12m distance at 3 Gbps
Applications
  • Central Information Displays
  • Rear-Seat Entertainment Systems
  • Audio/Video Systems
  • Device Gateways
  • Infotainment Head Units
INAP395R Application

  

Soft- and Hardware Tools

TOOL

DESCRIPTION

ORDER ID:

INAP395R Receiver Board

INAP395R APIX2 Receiver main board, Power Supply, 2m USB cable, Documentation, LVDS Display interface, HDCP license necessary

APIX2_ADK_RX_INAP395R

INAP375R Extender Board

APIX2 Receiver Extender Board, 5x FFC cable

APIX2_ADK_RX_EXT

INAP375T/R Ethernet Board

APIX2 Ethernet Extender Board for Transmitter and Receiver Main board, 5x FFC cable, 2m Ethernet cable

APIX2_ADK_ETH

APICO

Software Tool to configure APIX2 devices, configuration wizard, dependency check, plausibility check, status registers, etc.

Download

IBIS Model

IBIS Software Model of INAP375T

Download

 

LANDING PATTERNS

FORMAT

ZIP

Allegro

395R

Altium

395R

PADS

395R

BXL

395R

Application Notes

APPLICATION NOTES

DESCRIPTION

DOWNLOAD

AN202

POA: Power over APIX

Login or register

AN203

APIX2 Transfer Channel Requirements

Login or register

AN204

APIX2 Physical Layer Compliance

Login or register

AN206

INAP3xxT/R Diagnostic Features

Login or register

AN207

APIX2 - Transmitter Line Driver Setup

Login or register

AN208

APIX2 Daisy Chain Setup

Login or register

ORDERING INFORMATION

PART NUMBER

PACKAGE

PACKAGING UNIT

TEMP

STATUS

NAP395R-T

LQFP_100 14x14 mm

90 Tray

-40°C-105°C

active

INAP395R-R1

LQFP_100 14x14 mm

1000 Reel

-40°C-105°C

active